waterbrazerzkidai.blogg.se - Cp2104 usb to uart bridge controller driver windows 7

#CP2104 USB TO UART BRIDGE CONTROLLER DRIVER WINDOWS 7 INSTALL#
#CP2104 USB TO UART BRIDGE CONTROLLER DRIVER WINDOWS 7 DRIVERS#
#CP2104 USB TO UART BRIDGE CONTROLLER DRIVER WINDOWS 7 CODE#

I have been solving the same problems for a long time with many ESP8266 as well as ESP32 development boards (NodeMCU, D1 etc…).

#CP2104 USB TO UART BRIDGE CONTROLLER DRIVER WINDOWS 7 DRIVERS#

General problems with USB cables and UART chips and instability of Windows drivers

#CP2104 USB TO UART BRIDGE CONTROLLER DRIVER WINDOWS 7 INSTALL#

Driver Management concluded the process to install driver silabser.inf_amd64_dfdf591955e10cae for Device Instance ID USB\VID_10C4&PID_EA60\0001 with the following status: 0x0.Ĭontinuing the discussion from CP210x driver does not work with ESP32 on Windows 10:.

Driver Management has concluded the process to add Service silabser for Device Instance ID USB\VID_10C4&PID_EA60\0001 with the following status: 0.Ģ2-May-20 16:09:06 - Device installed (silabser.inf_amd64_dfdf591955e10cae).

Device USB\VID_10C4&PID_EA60\0001 requires further installation.Ģ2-May-20 16:09:06 - Driver service added (silabser).

So the hub seems to be the issue.Ģ2-May-20 16:09:06 - Device install requested: However, I just tried it with an USB-C to micro cable, et voila, ESP32 functions normally.

#CP2104 USB TO UART BRIDGE CONTROLLER DRIVER WINDOWS 7 CODE#

This morning, I connected the ESP32 through the hub, and the device was working! Couple hours later, tried again, same error code 10.

Yeah you are right, forgot to disclose that I bought it on Aliexpress, and contacting them for these kind of problems seems pointless.Īlso, I am using an USB-hub, since my laptop has only USB-C ports. Well super-strictly said they meant the vendor of the USB-UART adapter or board that incorporates that chip… String descriptors are not available (because the device has problem code CM_PROB_FAILED_START) Endpoint Descriptor -īDescriptorType : 0x05 (Endpoint Descriptor)īEndpointAddress : 0x81 (Direction=IN EndpointID=1)ĭata (HexDump) : 07 05 81 02 40 00 00 Endpoint Descriptor -īEndpointAddress : 0x01 (Direction=OUT EndpointID=1)ĭata (HexDump) : 07 05 01 02 40 00 00 String Descriptors.

Configuration Descriptor -īDescriptorType : 0x02 (Configuration Descriptor)īConfigurationValue : 0x01 (Configuration 1)

IManufacturer : 0x01 (String Descriptor 1) IdVendor : 0x10C4 (Silicon Laboratories, Inc.) Device Descriptor -īDescriptorType : 0x01 (Device Descriptor)īDeviceClass : 0x00 (defined by the interface descriptors) Connection Information V2 -ĭevIsOpAtSsOrHigher : 0 (Is not operating at SuperSpeed or higher)ĭevIsSsCapOrHigher : 0 (Is not SuperSpeed capable or higher)ĭevIsOpAtSsPlusOrHigher : 0 (Is not operating at SuperSpeedPlus or higher)ĭevIsSsPlusCapOrHigher : 0 (Is not SuperSpeedPlus capable or higher)ĭata (HexDump) : 01 00 00 00 10 00 00 00 03 00 00 00 00 00 00 00. Connection Information -Ĭonnection Status : 0x01 (DeviceConnected) Power State : D3 (supported: D0, D3, wake from D0) Status : 0x01806400 (DN_HAS_PROBLEM, DN_DISABLEABLE, DN_REMOVABLE, DN_NT_ENUMERATOR, DN_NT_DRIVER) Output USBview (USB Device Tree): = USB Port1 =Ĭonnection Status : 0x01 (Device is connected)ĬompanionHubSymLnk : USB#ROOT_HUB30#7&10a4fe21&0&0#Ĭapabilities : 0x14 (Removable, UniqueID) Any ideas of what I can try to get it to work? So the device VID is 10C4 and the PID is EA60, so I believe I should be able to use the normal drivers. I can get the ESP32 to work on my Ubuntu system, with the drivers that come pre installed with Ubuntu. Reinstalling drivers, rebooting, trying different USB HUBS and cables, trying the windows 7/8 drivers, nothing works. I keep getting “The device cannot start (Code 10)”. No matter what I try, I cannot get the device to work. The Silabs chip on the device has the following information: I bought a cheap ESP32 dev kit, and installed the CP210x drivers for it (found here: ). Perhaps a bit of topic on this forum, but Silabs cannot help me unfortunately, so I thought let’s give it a try.